Hobby Caravans BEACHY Owner's Handbook (2027)
Official technical documentation and workshop diagnostics for Hobby Caravans BEACHY Owner's Handbook (2027).
Master Troubleshooting & Diagnostics Matrix
| Error Code / Indicator | Symptom / Meaning | Step-by-Step DIY Fix | Suggested Actions |
|---|---|---|---|
x_x_x_x | ETS Plus blinking green (fast) Possible Cause: Brake intervention or auto-test | Possible to continue driving. | DIY Safe |
x___x___ | ETS Plus blinking green (short pulses) Possible Cause: In power-saving mode | Possible to continue driving. After driving for approx. 3 seconds, the system will switch to ready mode. | DIY Safe |
xxx__xxx__ | ETS Plus blinking green (slow) Possible Cause: System or brakes too hot | Continue to drive with care. After 120 seconds, the cooling system will switch to ready mode. | DIY Safe |
_x_______ | ETS Plus blinking red light Possible Cause: Electric supply fault (e.g. loose contact or voltage too low) | Check the (plug-in) cabling. Unplug the system for 20 minutes, then plug it in again. If this does not help: contact a dealer/authorised specialist. | DIY Check / Tech Fallback |
_x_x_____ | ETS Plus blinking red light Possible Cause: Mechanical fault (e.g. no brake cable connected/ brakes badly worn out/ system installed incorrectly) | Visual inspection of brakes/assembly of ETS Plus/ check that braking system is properly adjusted. Unplug the system for 20 minutes, then plug it in again. If this does not help: contact a dealer/authorised specialist. | DIY Check / Tech Fallback |
_x_x_x___ | ETS Plus blinking red light Possible Cause: Error in the central unit (e.g. handbrake is on/ brake rigging preloaded during assembly) | If necessary, release the handbrake (overrunning equipment should be fully extended). If necessary, check that the brake rigging is properly adjusted. Unplug the system for 20 minutes, then plug it in again. If this does not help: contact a dealer/authorised specialist. | DIY Check / Tech Fallback |
N/A | ETS Plus LED does not light up Possible Cause: ETS Plus is inactive | Unplug 13-pin trailer cable from tow vehicle. Visual inspection of plug and contacts. Check that there is steady plus on the socket. Plug in 13-pin trailer cable to the tow vehicle. If this does not help: contact a dealer/authorised specialist. | DIY Check / Tech Fallback |
N/A | Noises occurring while towing the caravan Possible Cause: 1. Painted (dacromet coated) ball on the tow vehicle. 2. A galvanized or varnished tow ball on the tow vehicle. 3. A damaged, rusty or dirty tow ball on the tow vehicle. 4. Dirty or worn out friction pads in the hitch. 5. The towbar or brake rod in the linings of the overrunning equipment are running dry. | For painted, galvanized, varnished, damaged, rusty or dirty tow balls, or dirty/worn friction pads, refer to the sections 'Tow ball on towing vehicle' and 'Hitch'. For dry towbar or brake rod, use the lubricating nipple to grease the bushings, remove the gangway bellows and grease the exposed tow bar, and clean the removable tow ball on the locking mechanism and grease it again. | DIY Safe |
Beeps | Smoke detector warning signal beeps Possible Cause: Block battery is discharged or needs replacement. | Carefully turn the cover of the smoke detector anti-clockwise until it can be removed from its mount. Take out the used block battery and unpin it from the pins. Connect the new block battery (type 9VDC 6F22) to the pins, ensuring that the pins click into place on the poles. Place the battery in the battery container. Place the cover so that the holes for the lock are over the locking pegs and carefully turn clockwise until it locks into the mount. | DIY Safe |
Frequently Asked Questions
Q: How do I fill the fresh water tank?
Place the trailer in a horizontal position and shut the water tap. Unlock the filler cap with the key, give the blue cap a strong turn anti-clockwise and remove it. Fill the water tank using the fresh water filler neck (marked by a blue cap and water tap picture). Open the water tap and leave it open until water flows out without bubbles, then shut the tap. Put the blue cap back on, turn it clockwise, and lock it with the key.
Q: How do I empty the water system to prevent frost damage?
Switch off the electricity for the water pump, open the water tap to the centre setting, unscrew the cap on the cleaning port of the fresh water tank, unscrew and remove the overflow pipe in the fresh water tank, and take out the water pump and hold it up until the water pipes have emptied completely. Check whether the tank, faucets and pipes have emptied completely (use compressed air at max 0.5 bar if necessary), clean and rinse the tank, leave faucets open, and let the system dry for as long as possible.
Q: How do I prepare the portable toilet waste-holding tank for use?
Separate the two detachable sections of the toilet. Remove the cap from the pour out spout while it is pointing upwards. Add the correct dosage of waste-holding tank toilet additive, and add the correct dosage of water to ensure that the bottom of the waste-holding tank is covered. Shut the water filler funnel tightly and recombine the tanks.